Skip to Content.
Sympa Menu

opal - [Opal] RBend reference particle trajectory properties

opal AT

Subject: The OPAL Discussion Forum

List archive

[Opal] RBend reference particle trajectory properties

Chronological Thread  
  • From: "Li, Zhi" <zql810 AT>
  • To: "opal AT" <opal AT>
  • Cc: "Boland, Mark" <mark.boland AT>
  • Subject: [Opal] RBend reference particle trajectory properties
  • Date: Tue, 24 Nov 2020 17:59:26 +0000
  • Accept-language: en-CA, en-US
  • Arc-authentication-results: i=1; 1; spf=pass; dmarc=pass action=none; dkim=pass; arc=none
  • Arc-message-signature: i=1; a=rsa-sha256; c=relaxed/relaxed;; s=arcselector9901; h=From:Date:Subject:Message-ID:Content-Type:MIME-Version:X-MS-Exchange-SenderADCheck; bh=EWV0EIr7/36M9GZYi1h7JfOjHx2aWtTxv1dRMxndAOc=; b=c/UysTawHs2FmfKbrqauXXY/BxDe9UZJZqnZi7AsNaX0Y12BzE8Aji0w7qH8v3iKGP9haQ7w3u0rW6O3M0yzKQCQ6sY13M9UE7ISgsnyD0hkByxOOM9liwfaoRCWIGKl7htWNyVAj4wUe7+dKEXANXC/6iqNbYQH1kLgVECWp4AjsHlcrTbPFf6f13/miOJK5NACyJAnr544aB/bVFm3U+uqPsCdkM8KQCSNJoa9QJzgj8bVAB8QoufbpOUTL9ppKJCPGlmCQpYCqZXzrL7Gqas9lN+793tu6WFxUJ9jqzWhhP7kqbobOq+0DPVFFFKG9MEGbmM0R9ffyVZXwy5Gdg==
  • Arc-seal: i=1; a=rsa-sha256; s=arcselector9901;; cv=none; b=SeHmPeD4IvUx0O4rVN64OK9GQCaNbaRSMIb84qTq5fPU/LA9IZ/0lT6zIvNznEC/09jrenU/4fjHpcaisug5wyKxLJ8FamoZRNYoBT6pqlLrDzxZP1IZrnRggo7O/nrz1VuvnpCrDgyoZ4nNTrZ4ytVsYaT8BIrYnJeBjRQsfEnHsnGYSDpQQyn0ThuTDPjVLLckdXhgT3egsmSVpaFhAoeA2ctHc8lYc74bA8N+hO/tB5hD2iHQykB+P/i/a5GXj4/IbYZrtfUx1YZDliWOvXisJnZIDTqtc5qe4DeHxwt0gy/m1qfssJu5wqnENJa/4ykz+H/9N9KZOXpF/6njyQ==
  • Authentication-results: localhost; iprev=pass ( smtp.remote-ip=; spf=pass; dkim=pass header.s=selector2 header.a=rsa-sha256; dmarc=pass
  • Authentication-results:; dkim=none (message not signed) header.d=none;; dmarc=none action=none;

Hello OPAL-Team,

I'm currently learning to add a RBend component in OPAL-T. 
The input file is a modified version of the example file.

I added the following to the input file (from the OPAL manual):

Bend: RBend, ANGLE = 30.0 * Pi / 180.0,
ELEMEDGE = 0.25,
L = 0.5,
GAP = 0.02;

After the simulation finish running, I don't see any output describing the reference trajectory properties. I was expecting this information to be written in the (.out) file.

Please let me know where this information is stored. Thanks!

Best regards,


Attachment: input and field
Description: input and field

Archive powered by MHonArc 2.6.19.

Top of Page