The OPAL Discussion Forum

["Adelmann Andreas (PSI)" <andreas.adelmann AT psi.ch>]

opal inputfile.in --info 2

 see also http://amas.web.psi.ch/opal/Documentation/master/index.html#sec.introduction.output 

Cheers A

------
Dr. sc. math. Andreas (Andy) Adelmann
Head a.i. Labor for Scientific Computing and Modelling 
Paul Scherrer Institut OHSA/ CH-5232 Villigen PSI
Phone Office: xx41 56 310 42 33 Fax: xx41 56 310 31 91
Zoom ID: 470-582-4086 Password: AdA
-------------------------------------------------------
Friday: ETH HPK G 28   +41 44 633 3076
============================================
The more exotic, the more abstract the knowledge, 
the more profound will be its consequences.
Leon Lederman 
============================================

On 24 Nov 2020, at 22:05, Li, Zhi <zql810 AT mail.usask.ca> wrote:

Hi Anastasia and Christof, 

I not sure if I know how to increase the verbosity of the output. 

Do you mean adding something to the end of the command line?

Originally, I did not have the command line:

OPTION, INFO=TRUE;

After adding this line and running the code again, I still don't see the information I'm looking for. 

Perhaps I need a specific DMP option like the ones shown below?

<image.png>

Best regards, 

Zhi

---

From: Anastasia Ierides <aaierides AT gmail.com>
Sent: November 24, 2020 1:55 PM
To: Li, Zhi <zql810 AT mail.usask.ca>
Subject: Re: [Opal] RBend reference particle trajectory properties

 

Hi Zhi,

 

In addition to what Christof responded, is your INFO option set to TRUE inside your input file? (i.e., OPTION, INFO = TRUE;

 

Best,

 

Anastasia

On Tue, Nov 24, 2020 at 11:46 AM Li, Zhi <zql810 AT mail.usask.ca> wrote:

Hi Christof, 

After adding the line

OPTION, LOGBENDTRAJECTORY=TRUE;

I do get the trajectory file. 

However, I also want to see the trajectory properties output like the picture below.  

<Outlook-ys3411gv.png>

How do I get the code to write this information on the (.out) file?

Best regards, 

Zhi

---

From: Christof Metzger-Kraus <christof.j.kraus AT gmail.com>
Sent: November 24, 2020 1:11 PM
To: Li, Zhi <zql810 AT mail.usask.ca>
Cc: opal AT lists.psi.ch <opal AT lists.psi.ch>; Boland, Mark <mark.boland AT usask.ca>
Subject: Re: [Opal] RBend reference particle trajectory properties

 

CAUTION: External to USask. Verify sender and use caution with links and attachments. Forward suspicious emails to phishing AT usask.ca

Hi Zhi,

if you add 

OPTION, LOGBENDTRAJECTORY=TRUE;

to your input file then you should find a file in the directory 'data' containing the trajectory of the reference particle.

Best regards,

Christof

On Tue, Nov 24, 2020 at 7:00 PM Li, Zhi <zql810 AT mail.usask.ca> wrote:

Hello OPAL-Team,

I'm currently learning to add a RBend component in OPAL-T. 

The input file is a modified version of the example RFphotoinjector.in file. 

https://gitlab.psi.ch/OPAL/src/-/wikis/RFPhotoInjector

I added the following to the input file (from the OPAL manual):

Bend: RBend, ANGLE = 30.0 * Pi / 180.0,

FMAPFN = "1DPROFILE1-DEFAULT",

ELEMEDGE = 0.25,

DESIGNENERGY = 10.0,

L = 0.5,

GAP = 0.02;

After the simulation finish running, I don't see any output describing the reference trajectory properties. I was expecting this information to be written in the (.out) file.

Please let me know where this information is stored. Thanks!

Best regards,

Zhi